Mold Temperature Controller
Innovated product: TCM -12NC

This is necessary device and the key to raise high competition in the industrial circles.

 

3 innovations, 10 special features is the necessary to raise high productivity !

 Emit alarm if the cooling-water shortage occurs
Automatically change into cooling process if the temperature of hot medium is above setting temperature 10 oC. By applying cooling-water it will lower the heat into the set-up range. With the special designed pressure switch, the alarm system will emit to warm the shortage of cooling-water. (Patent still pending)
Prevent the cooling-water enters reversely
  Cooling-water must flow through the electromagnetic valve first then into the cooler. After heating-exchange process, hot water will be drained out. If the direction goes wrong, the heating-exchanged hot water would get through the electromagnetic valve first, then the electromagnetic valve would be burned. With equipped the prevent reversal valve to prevent cooling-water enters reversely. (Patent still pending)
Pressure gauge
 
*
 When finishing the installation at the first time switch on the pump, then pressure gauge will show the negative numeral if the PMMP runs reversely. It will be fine after changing any electric line and swich on again.
 
*
 Show the pressure numeral in the normal operation to know the flow through the tube.
 
*
 When pushing the clear button, it shows the negative numeral.
Equip thermometer on the hot medium joints
  Equipped with thermometer on the hot medium joints to show the temperature of "TO MOLD" and "FROM MOLD" very clearly.
Tube cleaning button
  When pushing the button, then PUMP reverse running at moment to produce the powerful momentum to clean tube circuit. (Patent still pending)
Over heat protection controller
  With adjustable over-head controller to protect the hot medium oil and PUMP. If the temperature is over the set-up value, it will be cut-off automatically. (Max setting 150oC)
Use SPECK PUMP
  Use SPECK PUMP, which is the most famous brand in the world. Over heat protection controller
Use TEW.HT.BAND HEATER
  Most direct-heating designed machine will cause the greaves due to the medium liquid is contacting with the high temperature surface of the tubular heater directly. It will burn out the tubular heater and decrease the oil circulation efficiency. With equipped TEW.H.T.BAND HEATER which is heating indirectly and reliable for long-term use. Can avoid the above disadvantages.
Hard copper tubes
  All the piping is adapted into hard copper tube and direct connected joints. They are tough and endurable.
Equip ventilated window
  The new designed ventilated window works very well to reduce the inner temperature thoroughly to be near the outside temperature. It allows seeing the operation inside through it or removing it for the convenience of maintenance.
   
Improve production efficiency and assure injection quality
   
Starting from forming operation, the mold-temperature will be unstable thus tend to produce bad products. TCM is based on the principle of heat exchange to control the mold temperature in a setting range.
TCM can be pre-heating before suing and make the mold reach the required temperature quickly, temperature can be property maintained to ensure super quality of the product regardless of initiation of injection molding or continuing operation or momentary shut down.
Well-designed and is suitable for forming molds, roller-machines and heating groovers.
Heat medium liquid: Water or oil convertibly. Either water or oil can be the medium liquid in complicance with mold temperature for molding.
 
TEW Across Century Newly Developed Product
New Model No. TAL-600NC
 

New Automatic Loader (Model No. TAL -600NC) with Bigger Capacity but Lighter Weight, Stronger Vacuum Suction, Higher Performance, Increased Reliability & Durability. New creative design, enhanced function allows compatibility with most industry plastic machinery. Easy to Install on the Hopper Dryer of various size of injection machine directly and make the work more easily and conveniently.

 
The new creative design allows the filter device to be located outside of the material tank. It will be more convenient for both cleaning and replacement of filter to avoid the trouble of the separated installation.
Motor, filter and material tank are connected directly. The structure of filter device is nearly inbuilt but also with the convenience of out side installation, while with out the trouble of separated long-distance conveying connection
1 HP, 2P ,3 strongly Induction Motor produces the suction power above 2500mmAq. It is no necessary to change the carbon brush, it's stronger suction and more durable.
New material tank made from stainless steel with larger capacity while lightweight design suitable for installing on the Hopper Dryer directly. With loading volume to 16kg each time, conveying capacity above 600kg/h, compatible with various size of injection machine.
To adopt Microprocessor to control the operation with multiple functions, especially it will auto-reverse periodically to assist the cleaning of filter automatically.
   
Specifications
Motor
Static Wind Pressure
(MAX)
Storage Tank Capacity
Conveying Capacity
Weight
Induction Motor
1HP, 2HP, 3
2500 mmAq
16kg
600 kg/hr
30kg
Filter Size
External Dimensions
Conveying hose Inner Diameter
Conveying Hose L
Spere Part
100 x 260 mm
500(W) x 450(D) x 550(H) mm
38 mm
3.6 m
Filter x 1

Installation
1.
 Install the TAL -600NC on the hopper dryer, then connect the conveying hose to the suction nuzzle of TAL -600NC.
 
2.
 Connecting the power supply.
Features
 
1.
 Keep the hopper dryer always full to get enough drying. To eliminate the loss caused by manual loading.
 
2.
 Automatic loading to get timesaving and laborsaving.
To maintain the neatness and cleanliness required by the modern factory.

TEW Electric Heating Equipment CO., LTD
7F, No.140, Sec. 2, Nan Kang Road, Taipei, Taiwan, R.O.C
TEL : 886 - 2 - 27887728 FAX : 886 - 2 - 27887630
E-mail :info.tew@msa.hinet.net, service@tew.com.tw

NEWLY DEVELOPED MODELS